| Notes: 1: Bumper fascia must be removed and replaced during installation., 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.Notes: 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major)., 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model., 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.Notes: 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation., 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper., 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.Notes: 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.: 12: Baseplate has non-24" spaced attachment tabs. Requires either a motorhome mounted tow bar or an adapter to utilize a car mounted tow bar. The SO:BX88153 adapter can not be used on non 24" baseplates. Tow bar adapters are not to be used with vehicles weighing over 5000 lbs., 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.: 12: Baseplate has non-24" spaced attachment tabs. Requires either a motorhome mounted tow bar or an adapter to utilize a car mounted tow bar. The SO:BX88153 adapter can not be used on non 24" baseplates. Tow bar adapters are not to be used with vehicles weighing over 5000 lbs.: 12: 2 different tie downs replacements can be found on the 84-85 Honda Accords & 88-90 Acura Legends. A measurement must be taken from the center of the first bolt going up into the sub-frame directly behind the tie down plate to the center of the eye on the tie down plate. If the measurement is approx. 3 1/2", use the 1503-1 bracket. If this measurement is approx. 4 3/4" use the 1505-1 bracket.Notes: 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.: 12: Baseplate has non-24" spaced attachment tabs. Requires either a motorhome mounted tow bar or an adapter to utilize a car mounted tow bar. The SO:BX88153 adapter can not be used on non 24" baseplates. Tow bar adapters are not to be used with vehicles weighing over 5000 lbs.: 12: 2 different tie downs replacements can be found on the 84-85 Honda Accords & 88-90 Acura Legends. A measurement must be taken from the center of the first bolt going up into the sub-frame directly behind the tie down plate to the center of the eye on the tie down plate. If the measurement is approx. 3 1/2", use the 1503-1 bracket. If this measurement is approx. 4 3/4" use the 1505-1 bracket.: 19: Soft bottom edge of bumper must be compressed rearward about 1-1/2”, 1: Bumper fascia must be removed and replaced during installation.: 1: Trimming of spoiler, air dam, grille or plastic fascia may be required on some models of this vehicle.: 3: Requires some drilling (not major).: 3: Trimming the lower air dam, air deflector, cowling and/or rock guard is required on this model.: 3: Baseplate is concealed through the air dam.: 9: Tow hooks must be removed and remain off the vehicle after installation.: 9: Due to the different front-end trim packages used on these Ford & Mercury cars, it may be necessary to take a measurement in order to obtain the proper bracket kit #. The measurement is taken from the front bottom face of the frame, where it ends just behind the bumper (below the radiator). If the measurement is:9 1/2" or less-use the 421-1 bracket. 11 1/2" or less use 417-2 bracket 13 1/2" or less use the 415-1 bracket. Use the 417-3 bracket if there's no painted plastic under the bumper.: 9: Baseplate is adaptable to BlueOx tow bars with a 3-prong clevis.: 12: Baseplate has non-24" spaced attachment tabs. Requires either a motorhome mounted tow bar or an adapter to utilize a car mounted tow bar. The SO:BX88153 adapter can not be used on non 24" baseplates. Tow bar adapters are not to be used with vehicles weighing over 5000 lbs.: 12: 2 different tie downs replacements can be found on the 84-85 Honda Accords & 88-90 Acura Legends. A measurement must be taken from the center of the first bolt going up into the sub-frame directly behind the tie down plate to the center of the eye on the tie down plate. If the measurement is approx. 3 1/2", use the 1503-1 bracket. If this measurement is approx. 4 3/4" use the 1505-1 bracket.: 19: Soft bottom edge of bumper must be compressed rearward about 1-1/2”: 19: On 95-96 Eagle Summits, inspect the bumper. If white or dark gray, use 803-1. If silver, there is no bracket available. |